60 Hz
COUNTERFLOW HEAT RECOVERY UNIT AND EC MOTOR FOR FALSE CEILING. EFFICIENCY 83%
MANUFACTURING FEATURES
CHASIS
• Internal support structure in hot-dip galvanized steel profiles Z140; construction in accordance with EN1886, mechanical resistance class D1.
• External casing made of sandwich panels,25 mm thick and in 6/10 thick sheet steel.
• Internal sheets hot-dip galvanized Z140, external sheets pre-lacquered RAL 9010 and covered with a protective PVC film.
• Internal insulation using high-density polyurethane foam (40 kg/m³). Airtightness guaranteed by an adaptable and resistant neoprene gasket.
• Opening panels, tightened by push screws that ensure adequate and constant pressure on the sealing joints.
• AISI 304 (EURONORM 1.4301) stainless steel condensate collection tank, internally sloped to facilitate drainage, in correspondence with the areas subject to condensation.
HEAT EXCHANGER
• Aluminum counterflow heat exchangers, whose efficiency certified by Eurovent exceeds the requirements established by the ecological design regulation No. 1253/2014/EU.
• Sized to achieve the best balance between heat recovery efficiency, pressure drops and electrical consumption of the fans.
• The heat exchangers also integrate a bypass damper (100% of the air flow) with automatic control to achieve the free-cooling and free-heating functions provided for by the aforementioned Ecodesign regulations.
• Inclined set to facilitate the discharge of condensates and simplify the start-up of the machine.
FILTERS
• Each OREQA series recovery unit is equipped with 1 ePM1 50% (F7) extraction filter and another ePM1 50% (F7) supply filter, both mounted on guides with gaskets for effective sealing and placed upstream of the internal components to guarantee adequate protection.
•Optionally, an ePM1 80% (F9) filter can be requested in supply side.
MOTOR-FANS
• Centrifugal fans in galvanized steel, independently controllable. With forward curved blades, aerodynamic profile, statically and dynamically balanced. Directly coupled to electronically commutated type motors (EC brushless), thermally protected and regulated by a 0-10V modulating signal.
ELECTRONIC CONTROL
• Supplied with an advanced electronic display, which includes temperature probes in the external air intake and the ambient air intake, which supervises their operation. The user interface consists of a remote control panel with an LCD screen.
•There are 3 control modes, all with Modbus communication protocol to integrate the unit in the most modern home automation systems through the RS485 serial port, supplied as standard.
-Control BASIC
-Control EVO COP (Constant pressure)
-Control EVO CAV (Constant airflow)
BYPASS
• Automatic by-pass damper 100% of the airflow rate.
RANGE
• 7 construction sizes.
• Circular connection from Ø150 to Ø315mm, depending on the model.
• Vertical and horizontal configuration.
• Flows up to 400 and 4.000 m³/h.
• Factory configurable only. Standard configuration H2 and V1.
• 3 controls with Modbus.
APPLICATIONS
• Designed for mounting in a false ceiling, in residential and commercial environments.
• For outdoor use, the installation of a weather protective roof is mandatory.
• In full compliance with the requirements of Ecodesign Regulation No. 1253/2014/EU, in force since January 2018, the devices in the OREQA range guarantee high standards of comfort and health in enslaved environments, optimizing the general energy balance and against a particularly low power consumption.
• Suggested minimum outside temperature of -5°C.
| A | B | C | D | E | F | G | H | I | L | M | N | Ø | Ø IN | Ø OUT | Ø SC |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1350 | 1000 | 380 | 288 | 455 | 478 | 276 | 246 | 184 | 230 | 71 | 173 | 200 | 1/2" M | 1/2" M | 1/2" F |
MANUFACTURING FEATURES
• Circular outdoor flange with bird guard made of galvanized steel.
Duct sensor for measuring temperature, relative humidity and CO2 in the rooms.
Optional: The CO2 modules can be removed from the sensor to be calibrated.
The sound attenuators are used to absorb the noise in air conditioning or ventilation ducts.
Casing in galvanised steel, thickness 0,8 mm;
Mounting flange with quick attack;
Acoustic material in mineral wool 50 Kg /m³ with protection against erosion by glass fibre fire resistance M0 and extended metal sheet
UNDER REQUEST:
Stainless steel execution
• It consists of a kit including the 3-way valve for the control of the water flow, to be combined with the hot and/or cold water coil, and its modulating electric actuator.
• Connection and fitting devices not included (to be arrange for by the installer).
• Protective roof for outdoor.
Filtration for air treatment units equipped with a pre-filter upstream, and air-conditioning units.
• High filtration area, high efficiency, compact and economic filter.
• Media: Mini pleat fiberglass paper
• Frame: Galvanized steel
• Maximum T° in continuous service: 100°C
• Humidity: 100% RH
• Tested for food contact according to CE 1935/2004
• Certified for microbial development (ISO 846-VD 6022)
• The automatic defrost system consists of a self-regulating electric coil in PWM mode of the input power, installed on the return air intake.
• The system is controlled by a special temperature probe positioned on the exhaust air and guarantees a considerable reduction of the input power compared to the traditional systems available on the market.
All units may be equipped with an internal re-heating electric battery, made up of armoured steel electric heaters, supplied complete with PWM control system, safety thermostat already wired and installed on board.
• The hot water coils are supplied in a dedicated section to be installed in the supply air-flow line. The casing has the same sizes and features of the main unit and it is fixed with a dedicated installation kit supplied with it.
• The coil is manufactured with copper pipes thickness 0,4 mm and aluminium fins thickness 0,11 mm.
• The pipes are mechanically expanded in the aluminium fins to increase the thermal exchange rate.
• On request, it is possible to install coils with different capacities from the standard ones, when previously agreed with the factory.
• The coil is manufactured with copper pipes thickness 0,40 mm and aluminium fins thickness 0,11 mm.
• The pipes are mechanically expanded in the aluminium fins to increase the thermal exchange rate.
•On request, it is possible to install coils with thermal performances different from the standard ones, when previously agreed with the factory. The cooling coil section is supplied complete with condensate drain pan with side water discharge.
+34 972 720 150
Control info