60 Hz
WALL DESCENTRALIZED RESIDENTIAL RECOVERY UNIT WITH WIRED REMOTE CONTROL
MANUFACTURING FEATURES
• Decentralized residential recovery unit for single-stack use in combination with a remote control (available as an accessory), connected by cable, wall-mounted and flush-mounted.
• Designed to minimize the aesthetic impact of the installed product, they are characterized by a particularly low-thickness wall frame (only 17 mm).
• Ultra low power consumption (2.8W to 8.6W ), perfectly compatible with 24/7 operation.
• VMC unit for a single room, with alternating flows, with a very high efficiency heat recovery unit (up to 90%) and a ceramic exchanger cell in the form of a honeycomb.
• Fans with EC motor, to guarantee very low consumption, driven by low voltage and with shafts mounted on ball bearings.
• Extremely low noise levels, compatible with installation in living rooms (living room, study, bedroom) and use at night.
• Ventilation duct with damping mechanism, to avoid the risk of contaminants entering from the outside and to maximize thermal insulation in the event that the room is not occupied for long periods.
• Possibility of installation on exterior walls with a thickness between 300 mm and 700 mm (with optional accessory).
• Operation permitted in a wide range of outdoor temperatures (-20°/50°C).
• Degree of protection against dust and water: IPX4.
• Electrical insulation class: II (ground connection is not required).
• The remote control can manage up to a total of 6 decentralized recuperators.
SOME CONTROL FUNCTIONS
Using the remote control (must be ordered separately) you can access the following options:
• Selection of 3 operating modes: Heat recovery, normal ventilation without heat recovery, and air extraction.
• Speed Selection
• Boost speed
• Filter status LED indicator: off for clean filters and on if filters are dirty and need to be replaced.
APPLICATIONS
• Decentralized ventilation unit with heat recovery specifically designed for air exchange in residential spaces characterized by high levels of thermal insulation.
• For rooms up to 20m² for each recovery unit.
| A | B | C | D | E | F | G | H | ØI | ØJ | ØK | ØL |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 240 | 224 | 80 | 64 | 17 | 275 | 42 | 18 | 151 | 146 | 153 | 216 |
• The control can manage up to a total of 6 decentralized recovery units.
• In VENTILATION or RECOVERY modes, the recovery units will start to ensure the balance of the general flow in ventilation mode with heat recovery.
Heat recovery mode
• Winter: Extracted air from the room (hot) is exploited to pre-heating the air supplied to the room (cold).
• Summer: Extracted air from the room (cold) is exploited to pre-cooling the air supplied to the room (hot).
• The connected devices cyclically reverse the direction of fan rotation (extracting and introducing air into the environment) with a set cycle time.
• Speed adjustment (of devices) is automatic and ensures the correct ba-lance of the Input/Output flow rates.
Ventilation Mode
• The devices change internal environment air (without recovering heat).
- Even number devices extract air from the environment.
- Odd number devices introduce air into the environment.
• Speed adjustment (of devices) is automatic and ensures the correct ba-lance of the Input/Output flow rates.
Air Extraction Mode
• All connected devices extract air from the internal environment.
• The air flow rates are all in Output toward the external environment.
Input 230Vac 50/60Hz (N=Blue, L= Brown)
Output: 12 Vdc-2A 24W (+=Red, -= Black)
Working temperature: -10ºC/50ºC
Input 230Vac 50/60Hz (N=Blue, L= Brown)
Output: 12 Vdc-3A 36W (+=red, -= Black)
Working temperature: -10ºC/50ºC
Input 100-240Vrms 50/60Hz
Output: 12 Vdc-3A 36W
Working temperature: -10ºC/50ºC
Ferrita for wiring
Rigid PVC pipe (diameter 160 and length 700 mm) for wall mounting.
Metal panel “windbreak” for exterior in stainless steel sheet.
External rubber grille that can be installed from the inside wthi out the need for scaffolding.
90° Circular / Square Adapter for entry and exit through a window jamb.
Rectangular stainless steel grill for ACC window adapter kit
Rectangular grid in powder-coated stainless steel, white RAL 9003, for kit.
Sensor to control the air temperature in the room: allows automatic start or speed change of the combined product when the temperature exceeds the preset value, selectable by external trimmer and adjustable in the range 10°C - 40°C. A timer allows the appliance to operate for a predetermined time, which can be set during installation from 3 to 20 minutes, after the temperature has dropped below the predetermined threshold.
Single-phase 220-240V / 50- 60 Hz power supply. Wall installation.
The color white.
Maximum allowable load: 3A.
Enclosure for wall installation with IP20 protection.
Sensor for controlling the rate of relative humidity (RH) in the air: allows automatic start or speed switching of the combined product when the percentage of RH exceeds 65%. If the humidity does not exceed the threshold, the associated appliance turns on automatically a few seconds after the light is turned on and continues to operate, after it is turned off, for a preset time, which can be set during installation from 3 to 20 minutes .
Single-phase power supply 220-240 V / 50-60 Hz. Wall installation. The color white.
Maximum admissible load: 3 A.
Enclosure for wall installation with IP20 protection.
Sensor para el control de la tasa de humedad relativa
+34 972 720 150
Energy label