BOX BV PLUS 10/10

MANUFACTURING FEATURES

• Outdoor flange with bird guard.
• Made of galvanized Steel.
• VIS OUT = Outlet
• VIS IN = Inlet

MANUFACTURING FEATURES

• Structure in aluminum profile 30mm, nylon corners, galvanized sandwich panels with internal insulation rockwool (25mm thickness) class A1 (non-combustible) of 90kg/m3 density
• All panels are equipped with "fastening system" for the quick assembly and disassembly whenever required, either for cleaning, maintenance or exchanging of panels.
• Box is supplied without filters.

(Check the filter units needed for the drawer surface, BOX FILTER for KENTALBOX PLUS need 2 filter of each granulometry)

Filter cells for rough primary filtration for air treatment units or air intake grids.

• Thick synthetic media with high retention capacity pleated between 2 rigid screens.
• Large filter surface.
• Frame: galvanised,

• Maximum continuous operating temperature: 70°C
• Relative humidity: 100%

• Tested for food contact according to EC 1935/2004

Filtration for air treatment units equipped with a pre-filter upstream, and air-conditioning units.

• High filtration area, high efficiency, compact and economic filter.

• Media: Mini pleat fiberglass paper
• Frame: Galvanized steel

• Maximum T° in continuous service: 100°C
• Humidity: 100% RH

• Tested for food contact according to CE 1935/2004
• Certified for microbial development (ISO 846-VD 6022)

Filtration for air treatment units equipped with a pre-filter upstream, and air-conditioning units.

• High filtration area, high efficiency, compact and economic filter.

• Media: Mini pleat fiberglass paper
• Frame: Galvanized steel

• Maximum T° in continuous service: 100°C
• Humidity: 100% RH

• Tested for food contact according to CE 1935/2004
• Certified for microbial development (ISO 846-VD 6022)

MANUFACTURING FEATURES

• Allows duct connection.
• Made of galvanized steel.

Weather protective roof made of galvanized steel for BOX BD PLUS, BOX BV PLUS, BVFC F400 and BOX BV

MANUFACTURING FEATURES

• Specially designed for speed frequency control in ventilation applications.
• Ultra compact, simple operation and wide range of functions.

*Dial panel incorporated. Optional EMC filter.

Certifications: CE/UL/CSA/EN/GOST/CCC.

Protection index IP20.

The selection of SFC frequency drive speed controller must be made based on the maximum intensity absorbed by the fan to be regulated. The powers (kW) and the intensity for constant load refer to the normal duty (150% overload for 60 seconds). The intensity for quadratic load admits an overload of 110% during 60s.

SFC 230: Entrance 230V I, exit 230V III
SFC 400: Entrance 400V III, exit 400V III

EMC filter incorporated for models from 47A (included)

*Lineal load rated current

**Quadratic load rated current

MANUFACTURING FEATURES

• Safety start-stop switches according to IEC 60947-1 and IEC 60947-3.
• IP65 and always equipped an auxiliary contact.
• Useful for switching off the current before handling the fan.

*Máx. thermal current air (A)

MANUFACTURING FEATURES

• Support of great radial and axial elasticity.
• These low-profile, compact and elastic supports control the three directions of movement with large deformations in the rubber.
• It consists of two parallel armour adhered to the bell-shaped rubber and by a base with handles.
• These supports with handles have a threaded hole in their upper frame and are easy to install and fix.
• The steel protection washer allows it to withstand overloads by increasing its rigidity and protects the rubber from dripping hydrocarbons.
• Elastomer type NR or high quality elastomer. Working temperatures between -40ºC and + 70º C.
• Taking into account the tolerances of hardness in the elastomers, the mechanical characteristics of these series may differ.
• Range of 6 sizes and 3 different hardnesses (45-60-75) to fit a load range between 2 Kg and 1300 Kg.
      1. Soft: hardness A 45
      2. Average: hardness B 60
      3. Hard: hardness C 75

APPLICATIONS

• Very appropriate in the elastic suspensions of machines that present vibrations of horizontal components.

MANUFACTURING FEATURES

• Metal insulators designed to work with compression with 85% insulation according to the following arrows (travel in mm) and rpm:

Arrow (mm.)          r.p.m.
    20 mm          >600 r.p.m.
    30 mm          >500 r.p.m.

• Made of high quality elastic steel, with rectangular base and rubber mat to improve the grip. It treats of a resistant product and easy assembly, that avoids all type of vibrations of the fans to the structure of the premises.
• Operating temperature from -45 ° C to + 120 ° C.

APPLICATION

• To install under machines with rotating components, ventilation groups, fans, ventilation boxes, etc.